Modular Sidewall Belt Conveyor , Conveyor Belt Minimal Emissions Environemtal Friendly
General
This Sidewall belt conveyor with corrugated shield, in particular applied in conveying material in big inclination, for it with corrugated shield and horizontal clapboard belt. And it can widely used in coal, metallurgy, chemical industry, light industry, petroleum, port, mechanical etc to convey all kinds of bulk materials and the piece.
Density of handled bulk materials 500~2500kg/m3, max inclination is 90°, max lump size is 550mm, lump of handled should depends on belt width, belt speed, clapboard height and inclination.
Ambient temperature generally -25~+40℃, material temperature to be handled should be under 50℃. It should take other measures for special requirement such as heat resistant, proof cold, resistant retard, resistant acid and alkali, resistant abrasion, proof explosion, proof water etc.
Advantages And Features
Technical parameters for reference
Remarks: the below capacity is based on coal and speed 1m/s to caculated for reference.
| Bandwidth | 500mm |
| Cleats hight | 80mm | 120mm | 160mm |
| Pitch of cleats | 126mm | 252mm | 126mm | 252mm | 378mm | 252mm | 378mm |
| Slop | 30 degree | 39 t/h | 21 t/h | - | 52 t/h | 34 t/h | 65 t/h | 45 t/h |
| 40 degree | 31 t/h | 16 t/h | - | 40 t/h | 26 t/h | 52 t/h | 34 t/h |
| 50 degree | 25 t/h | 13 t/h | 60 t/h | 32 t/h | - | 42 t/h | 27 t/h |
| 60 degree | 20 t/h | 11 t/h | 50 t/h | 26 t/h | - | 34 t/h | 23 t/h |
| 70 degree | 17 t/h | - | 41 t/h | 21 t/h | - | 28 t/h | 18 t/h |
| 90 degree | 10 t/h | - | 25 t/h | - | - | 17 t/h | - |
Selection Conditions
- Material to be processed: _____
- Max. granule size of the feeding material: _____mm
- Handling capacity (Ps. It means the total material capacity feeding from the inlet): _____t/h
- Percentage of Max. granule in material:_________%
- Upstream equipment (Ps. It means what kind of Equipment is used to feed the material):____
- Bulk Density: _____t/m3
- Material temperature: _____℃;
- Downstream equipment (Ps. It means what kind of equipment is used to discharge the material): _____
- Water content:____%
- Material is corrosive or not: ____ (Ps. Yes or No)
- Working power supply: _____V ______HZ
- Material is sticky or not: ____ (Ps. Yes or No)
- Working environment is indoor or outdoor: _______
- Working environment temperature: ______ ℃
- Please refer to the following picture and provide the relevant parameters:L1____m, L2___m, H___m, α____°
Operation regulation and maintenance
- Belt conveyor should be operated in according to design requirement.
-
Belt conveyors are not allowed to overload run.
-
All safe alarming should be in good condition.
-
Check wear condition of the belt, the damaged should be repaired.
-
Operators should circuit to inspect to close observe belt conveyor running. Especially,temperature rise and noise of main motor and the brake working whether they are normal; contact state of the brake and oil level, noise of gear unit and run off of belt should be noticed;temperature rise and noise of all bearings and state of all transition loads point should be noticed;
notice to see whether the hopper are blocked, working state of pulley, idler, belt cleaner, take-ups and control equipment.
Product Tags:
|
|
Modular Sidewall Belt Conveyor , Conveyor Belt Minimal Emissions Environemtal Friendly Images
|
